Products
Current Location: >>Home >> Products >> Cellular Repeater Series >> RF Cellular Repeater >>IDEN 800M

IDEN 800M RF Repeater

Model
  • IDEN 800M:  UNRI3

Description

Picture of IDEN 800M RF RepeaterIDEN 800M RF Repeater is designed to solve problems of weak mobile cellular signal, which is much cheaper than adding a new Base Station (BTS). Main operation of RF Repeaters system is to receive low-power cellular signal from BTS via radio frequency (RF) transmission and then transmit the amplified signal to the areas where network coverage is inadequate. And the mobile signal is also amplified and transmitted to the BTS via the opposite direction.

According to your requirement for working frequency, you can choose either type of RF Repeaters:

  • Band Selective RF Repeaters System: to amplify all signals in the whole band (Various bandwidth is available upon request)
  • Wireless Channelized RF Repeaters System: to amplify only the signals transmitted by the customized 1 or 2 or 4 or 6 or 8 channel (A narrow band with customized central frequency)

Application
To expand signal coverage of fill signal blind area where signal is weak or unavailable.
  • Outdoor/Rural: Airports, Tourism Regions, Golf Courses, Tunnels, Factories, Mining Districts, Villages etc.
  • Indoor: Hotels, Exhibition Centers, Basements, Shopping Malls, Offices, Packing Lots etc
The Single Band GSM850, CDMA800 RFR is mainly applicable to such case:
  • The repeater can find an installation place which can receive pure BTS signal at strong enough level as the Rx Level in repeater site should be more than -70dBm;
  • And can meet the requirement of antenna isolation to avoid self-oscillation.

IDEN 800M Repeater installed on top of building for Outdoor Coverage


IDEN 800M Repeater installed on top of building for Outdoor Coverage

IDEN 800M Repeater installed on tower for Outdoor Coverage


IDEN 800M Repeater installed on tower for Outdoor Coverage

IDEN 800M Repeater installed for Inbuilding Solution


IDEN 800M Repeater installed for Inbuilding Solution


Specification
Specifications
Working Frequency (customizable) Uplink 806~824MHz
Downlink 851~869MHz
Working Bandwidth 19 MHz (customizable)
Output Power (customizable) 27~43 dBm (0.5~20 W)
Gain ≥ 85dB
Gain Adjustment Range 1~31dB @ step of 1dB
Voltage Standing Wave Ratio (VSWR) < 1.5
Noise Figure ≤ 5dB
In-Band Ripple ≤ 3dB p-p
Max. Input Level ≥ -10dBm
Spurious Emission Within working band ≤ -15dBm/30kHz
Out of working band
(Δf > 2.5MHz)
9kHz~1GHz: ≤ -36dBm/30kHz
1GHz~12.75GHz: ≤ -30dBm/30kHz
In-Band Intermodulation Attenuation ≤ -40dBc/30kHz (measured under rated output power)
System Delay ≤ 1.5μSec
I/O Impedance 50Ω
RF Connector N-Type (Female)
Temperature Range Operation: -25°C ~ +55°C / Storage: -30°C ~ +60°C
Relative Humidity Range ≤ 95% (non condensing)
Power Supply (customizable) DC +24V / AC 220V±15%, 50Hz / AC 110V±15%, 50Hz
Backup Power Supply (optional) 4 hours
Casing Level Output power @27~30dBm: IP31
Output power @33~43dBm: IP65
Dimensions Output power @27~30dBm: 385mm X 300mm X 130mm
Output power @33~37dBm: 570mm X 325mm X 215mm
Output power @37~43dBm: 630mm X 400mm X 230mm
Weight Output power @27~30dBm: 8kg
Output power @33~37dBm: 27kg
Output power @37~43dBm: 35kg
Remote Monitoring/Control via NMS Supported
AGC (Automatic Gain Control) /
ALC (Automatic Level Control)
Supported